Slim Mini Size Waterproof Wiegand 26/34 125KHz EM RFID Reader for Door Access Control Proximity RFID Reader Black Color
Electronics > Security & Surveillance > Accessories > Access-Control Keypads
About this item
- Card Type: EM-ID Card (Can't support HID, Cobra, APCiK etc)
- Type: EM RFID 125khz reader, Can't work alone, Normally work with Control board/Fingerprint devcie/Master controller to build completely Security Access Control System.
- Support Wiegand 26-Bit and Wiegand 34-Bit; Built-in LED (Double Color LED) and Loud Speaker (Buzzer).
- WatherProof, Water Proof, can Install outside,Small and Beautiful Reader.
- Intput Voltage: DC 9-15V, Can stable running for many years.
Reviews
★★★★★
Verified Purchase
Cheap and functional
I have two of these outdoors and four indoors. Replaced a name brand system, only difference is that cards/fobs are much cheaper.
★★★★★
Verified Purchase
Reads really far away, and support is awesome.
I just sent an email asking about setup at 3:30 in the morning, and just got a reply 20 minutes later. And it was helpful and informative, and I am now set up properly. Can't believe it. That NEVER happens anymore, and support usually sucks these days. What awesome support! In addition, the reader itself is very aesthetic, and reads from like 6 inches away. Which is pretty astounding and I've never had an RFID reader work so well. I can't believe this was only 15 bucks. Sometimes, you get wayyyyy more than you pay for!
★★★★★
Verified Purchase
6-inch sensitivity is a get
Our old card reader (defunct brand) failed and we went with a different product here on Amazon that was the same size. It failed miserably and required users to rub the card all over the reader to find the sweet spot. I opted to buy this smaller profile card reader and it does not disappoint. It can read a card from about 6 inches away and doesn’t require the removal of the card from a wallet or bag.
★★★★★
Verified Purchase
Works like a Champ!
Great little 125khz reader, not bad looking either and works without failure as compared to some other EM compatible card readers on Amazon
★★★★★
Verified Purchase
Great purchase
We purchased 4 of them in mid 2018 and they are all still working, even after enduring the wet, hot south florida weather for 3 plus years. So Yes I Highly recommend!
★★★★★
Verified Purchase
Works fine
Works fine, if it is outside use a weather box, if not it won’t last
★★★★★
Verified Purchase
Perfect
Perfect
★★★★★
Verified Purchase
High quality for a good price
Product work perfectly as described with a commercial based Access Control solution had no issues looks great looks to be built decently well highly recommended.
★★★★★
Verified Purchase
Good, working product
Didn't have to talk to Tech Support, so can't say anything about them
★★★★★
Verified Purchase
Great value
All good
Show for you like this post.
Question & Answer
Question :
can i add more keysfobs to this?
Answer :
this is just a reader, this reader need to work with our control panel and power box, to build a complete access control system.
can you send me amazon message email? so that I can send you more materials and discuss your requirement.
On the product page( ), search “sold by” and click on "SecureLife4you Security Control", then press: Ask a question
Any question is good question, I have over 20 years experience, my support is for ever.
BRs
Question :
is there a way to adjust the range to have maximum range?
Answer :
its low frequency reader, only read 3-5 cm
Question :
Looking for this exact model in white. Does it exist?
Answer :
Not that I have seen. There are other compatible readers in white.
Question :
does this need programed? i have it hooked up but i cant scan to allow the push process, my unit came with no paperwork
Answer :
it's just slave reader, need to work together with master controller such as:
or
Question :
can't find after move, where can I get the wiring manual for this?
Answer :
Connect the controller, Connect 5 wires
a. RED: DC +7V-24V to the +12V of controller
b. Black: DC-GND to the GND of controller
c. Green Data0 to D0 of controller
d. White: Data1 to D1 of controller
e. gray color wire of reader to the the GND besides 12V
Question :
Does this have doorbell?
Answer :
No
Question :
I have wires correctly connected to my eidc32 controller (green=d0/white=d1). blue light is on. no beep or anything when i swipe a hid card. help?
Answer :
Hi, connect Grey wire and Black wire to GND.
Question :
What voltage do the data wires operate at?
Answer :
it's DC12V
Question :
Is there a reason this is reading tags incorrectly?
Answer :
If you have a seperate USB reader for the tags you will read what the actual tag is. Once you put your tag on on the mini reader your security board will decode the actual reading to something else. So when you see it on the Access control application it will show different. This is normal I believe it is to make sure no one can copy your tag's information.
Question :
Will this work with 4 wire door access cable?
Answer :
Yes
Comments
Post a Comment